Trend 866x1/2tc Finger Jointer Set 1/2
Finger Jointer Combines An Assembley Of Five Tct Slotting Cutters With An Abutting-edge Cutter To Produce A Profile That Extends The Glue Line Threefold,
Trend 46/22 X 1/2 Tc Trimmer
Self-guiding Trimmers With Bearings Mounted On End Of Cutter.
For Trimming Plastic Or Plywood Overlay.
For Copy Profiling, Use The Bearing To Follow A
Trend 46/91 X 1/4 Tc Template Profiler
Profiler With Shank Mounted Bearing Guides.
For Use With Router Mounted Above Or Below A Table When Following A Template.
For Profiling And
Trend 46/92 X 1/4 Tc Guided Profiler
Profiler With Shank Mounted Bearing Guides.
For Use With Router Mounted Above Or Below A Table When Following A Template.
For Profiling And Re
Trend 46/94 X 1/2 Tc Guided Profiler
Profiler With Shank Mounted Bearing Guides.
For Use With Router Mounted Above Or Below A Table When Following A Template.
For Profiling
Trend C115ax1/4tc Trimming 9.5mm Dia X 25.4mm Cut
Used For Trimming Plastic Or Plywood Overlays.
Also For Copy Profiling With A Template.
Dimensions:
D=3/8 Inch
D=9.5 Mm
C=1 Inch
C=24.5 Mm
Trend C115x14 Tc S/guided Trimmer 9.5mm Dia
Used For Trimming Plastic Or Plywood Overlays.
Also For Copy Profiling With A Template.
Dimensions:
D=3/8 Inch
D=9.5 Mm
C=1/2 Inch
C=12
Trend C116x1/2 Tc S/guided Trimmer 12.7mm Dia
Used For Trimming Plastic Or Plywood Overlays.
Also For Copy Profiling With A Template.
Dimensions:
D=1/2 Inch
D=12.7 Mm
C=1 Inch
C=2
Trend C116x14 Tc S/guided Trimmer 12.7mm Dia
Used For Trimming Plastic Or Plywood Overlays.
Also For Copy Profiling With A Template.
Dimensions:
D=1/2 Inch
D=12.7 Mm
C=1 Inch
C=
Trend C117x1/4 Tc S/guided Trimmer 15.9mm Dia
Used For Trimming Plastic Or Plywood Overlays.
Also For Copy Profiling With A Template.
Dimensions:
D=5/8 Inch
D=15.9 Mm
C=5/8 Inch
C
Trend C119x1/4 Tc S/guided Bevel Trim A=65
This Is Bearing Guided And Gives A Smooth Bevel Finish For Laminates And Other Materials.
Bearing Follows The Board Beneath.
Dimensions:
D=
Trend C121x14 Tc Template/profile 12.7mm Dia
Shank Mounted Bearing Profilers Are Ideal For Template Guidance.
Use For Rebating And Trimming Edges Only.
Extra Care Must Be Taken To
Trend C123x1/4 Tc Template/profile 19.1mm Dia
Shank Mounted Bearing Profilers Are Ideal For Template Guidance.
Use For Rebating And Trimming Edges Only.
Extra Care Must Be Taken To Avoi
Trend C133x14 Tc Cove 10mm Rad & 20mm Dia
This 'roughing' Trimmer, Leaves An Overhang Of 3mm, For Secondary Final Trim.
Dimensions:
D=1/2 Inch
D=12.7 Mm
C=1 Inch
C=25.4
Trend C135x1/4 Tc Pierce/trim 6.3mm Dia X 18mm Cut
Cuts Out Apertures In Laminate Worktops.
The Nose Of The Cutter Acts As A Guide Follower.
Dimensions:
D=1/4 Inch
D=6.3 Mm
C
Trend C165x1/2 Tc Profiler 19.1mm Dia X19.1mm Cut
Shank Mounted Bearing Profilers Are Ideal For Template Guidance.
Use For Rebating And Trimming Edges Only.
Extra Care Must Be Taken To Avoid Cutt
Trend C166x1/2 Tc Profiler 19.1mm Dia X 50mm Cut
Shank Mounted Bearing Profilers Are Ideal For Template Guidance.
Use For Rebating And Trimming Edges Only.
Extra Care Must Be Taken To Avoid Cutte
Trend C167x 1/4tc Guided Trimmer 6.35mm Dia X 12.7mm
Used For Trimming Plastic Or Plywood Overlays.
Also For Copy Profiling With A Template.
Dimensions:
D=1/4 Inch
D=6.35 Mm
C=1/2 Inch
C=12
Trend C168x1/4 Tc Guided Trimmer 6.35mm Dia X 25.4mm
Used For Trimming Plastic Or Plywood Overlays.
Also For Copy Profiling With A Template.
Dimensions:
D=1/4 Inch
D=6.35 Mm
C=1 Inch
C=25.4
Trend C190x12 Tc Guided Thumb Mould 44mm Rad X 69.2mm Dia
A Quarter Ellipse Cutter For Architraves And Mould Finishes.
For Stationary Machines - 12000 Rpm Recommended Speed.
Dimensions:
D=69.2
Trend C192x12 Tc Offset Tongue And Groover 40mmm Dia X 32mm Cut
A Reversible Finger Jointer, To Increase The Gluing Area For Edge To Edge Joints.
Dimensions:
D=40.0 Mm
D2=31 Mm
C=32 Mm
Shank
Trend C194x12 Tc Staggered Mortice 16mm Dia X 50mm Cut
Deep Mortising And Grooving Giving Good Chip Clearance.
For Lock Mortising, Two Width Cuts Will Be Needed To Achieve The Standard 19mm Mortis
Trend C195x12 Tc Guided Trimmer 50mm Cut X 12.7mm Dia
Used For Trimming Plastic Or Plywood Overlays.
Also For Copy Profiling With A Template.
Dimensions:
D=1/2 Inch
D=12.7 Mm
C=50 Mm
B=12.7
Trend C196x12 Tc Guided Trimmer 38mm Cut X 12.7mm Dia
Used For Trimming Plastic Or Plywood Overlays.
Also For Copy Profiling With A Template.
Dimensions:
D=1/2 Inch
D=12.7 Mm
C=38 Mm
B=12.7
Trend C199x12 Tc Double Guided Trimmer 50mm Cut X 19.1mm Dia
Allows Templates To Be Placed Either On Top Or The Bottom Of The Material, For Ease Of Routing.
Dimensions:
D=19 Mm
C=50 Mm
B=19 M
Trend C200dx12 Tc Two Flute 12mm Dia X 63mm Cut (with Centre Tip)
Suitable For A Wide Range Of Applications Such As Engraving, Grooving, Rebating And Shallow Mortising.
Use On Softwoods, Hardwoods
Trend C200x12 Tc Two Flute 12mm Dia X 50mm Cut (no Centre Tip)
Suitable For A Wide Range Of Applications Such As Engraving, Grooving, Rebating And Shallow Mortising.
Use On Softwoods, Hardwoods, M
Trend C204x12 Tc Profile Bevel Set 41mm Dia X 10° Bevel
The Classic Method Of Producing Cabinet Panelled Door And Drawer Fronts Is Made Easy With These Profile Scriber Sets. With The Combinatio
Trend C205x14 Tc Triple Fluted Trimmer 25.4mm Cut X 12.7mm Dia
Self-guiding Triple Flute Cutter.
Extra Fine Trimming And Longer Life.
For Trimming Of Laminate Or Plywood Overlay.
Dimensions:
Trend C219x12 Tc Finger Jointer 35mm Dia X 38.1mm Cut
One Piece Tool To Increase Glueing Area For Edge To Edge Joint.
Dimensions:
D=35 Mm
C=38.1 Mm
B=19.1 Mm
Shank Diameter=1/2 Inch
Ol=90 M
Trend Mb/09x1/4tc Mini Guided Profiler 4.8mm Dia X 6.3mm C
Miniature Bearing Cutters Ideal For Sign-making, Musical Instrument Building And Other Small Intricate Projects.
Can Be Used On Wood And
D&M Tools are passionate about tools. As one of the largest and longest established independent tool retailers in the UK we supply professional power tools, hand tools, machinery and accessories .
We stock a huge range of power tools including cordless drills, cordless saws, cordless combi drills, cordless screwdrivers as well as routers and angle grinders.
Our machinery range includes, lathes, bandsaws, table saws, spindle moulders, planers and thicknessers and pillar drills as well as dust extractors, welders and water pumps.
D&M Tools also offer a huge range of hand tools and accessories from Irwin,Stanley,Bahcoand many more including hammers, screwdrivers, hand saws, clamps, spanners, chisels and wrenches.
We also stock an extensive selection of clothing and workwear including trousers, jackets, sweatshirts, hoodies, T-shirts, socks and footwear from top brand Snickers, Dickies, Apache and DeWalt
Great brands, Great deals and Great range backed up with our famous D&M service, why shop anywhere else?